Camera module
model:KS13A04(Different PCB board colors in different production batches)
product description
KS13A04Camera module,Using fine sizeCMOSThe sensor is designed to ensure high-quality images; the product can be used in tablet computers,Handheld, high-speed camera, detector…The finished product camera module has the characteristics of small size, intelligent focus, accurate color reproduction, clear images, low power consumption, and high reliability.…
1. Real shots
2. Specifications and characteristics
Front view Rear view
KS13A04Dimensions
Total size:30*25mm±0.2mm
Imaging size:160*120,176*144,320*240,352*288,640*480,1280*1080
IRAnti-infrared interference filter(IR Filter)
Three, performance and parameters
project | index | Remarks |
Optical structure | 3P | |
Field of view | 65° | Angle optional |
aperture | F2.8 | |
Relative contrast | 60% | |
Image transfer rate | 15/30 fps | format:VGA |
output signal | YUV | |
Output script | 24Pin | Pindistance0.65mm |
Color compression format | YUY2 | |
Operating Voltage | 3.3V~5V | |
distortion | ?0.5% | |
Wire | 1.5M(Optional) | |
1,rate5~30fps/s, Interpolation can reach1000CMOS
2, Using high-quality lenses
3,high speedUSB2.0Interface, fully compatibleUSB1.1
4, Plug and play, no driver required
5, Photosensitive device:high quality3inch,VGAformat
6, Letter-to-noise ratio: greater than48dB
7, Focusing method: manual focus
8, Scan mode: progressive scan
9,VideoData Format:8/16bit
10,Operating temperature:0°-40°
11, Image processing: exposure control/Gain control/White balance/Gamma correction
12, Fast compression engine,2to8Compression ratio
13,MMXTechnology high-speed soft decompression, the highest resolution can reach1280*1080dpi
14,support systemWindowsXP
15, Support dynamic and static image capture, supportvideoVideo recording
16,high quality64Bit true color, applicable shooting range:10cmTo100m
17, Video conference, video chat, video phone, file shooting
18, Color compression technology:YUY2
19,size:30*25mm(template)
Four, test data
Optical test
All tests are carried out in a dust-free environment;
Test board brightness: the brightness is400~500LUX, The brightness difference between the center and the four corners shall not exceed15%.
Resolution test
project | content |
Test chart | MTFTest chart |
condition(effective distance:10cm~∞) | Light source: cold light source Color temperature:6500K brightness450±50LUX |
MTFspecification | center/Four weeks:40 |
Vignetting test
project | content |
Test chart | Test chart(See below) |
condition | Light source: cold light source Color temperature:6500K Test height:400mm |
specification | No vignetting |
| |
This effect is an infrared lens effect
KS13A04Test chart(No shadow on the corners is normal)
Stain test
condition | specification |
The module faces the white light test board, and observe whether the screen is stained | The difference between the brightness of the swelling and the surroundings does not exceed5% |
Injury point/Dead pixel test
DEAD PIXEL(Dead pixels) | No reaction to light, it looks like either a white spot or a black spot. The brightness of the point will not change, this point is calledDEAD PLXEL. |
WOUNDED PIXEL(Injury point) | It will appear with irregular frequency due to the bright and dark light, and the dots will have different brightness due to the bright light. This point is calledWOUNDED PIXEL. |
Pixel | Total number of blocks | totalPLXEpoint | BlockPLXELpoint |
0.3 | 81 | 307200 | 3793 |
1.3 | 81 | 1336400 | 16,499 |
Environment?Reliability Test Conditions(Temperature test/Vibration test/Drop testspecification)
test | project |
1 | Free fall test | height:150cm, Six sides; |
2 | Vibration test | 30Hz,3g,3axis,60minute/Axial |
3 | Storage test(standard) | High and low temperature:-20°C~+70°C/each16hour |
4 | Humidity test(standard) | 65°C/95%RH/72hour |
5 | Operational test(standard) | -20°C2Time →55℃ each2hour |
6 | Loop test(standard) | -20°C/4Hours →70°C/4hour,10Times |
Five, matters needing attention
1, This product isCMOSproduct,Sensitive to static electricity,Please pay attention to the influence of static electricity when using, handling and storing;
2, Please do not touch the lens aperture with bare hands, so as not to shed finger marks at the aperture and affect the image quality;
3, This product is a more precise product, and mechanical collision should be avoided during use or handling;
4, During use,Avoid shooting directly in the sun,So as not to damage the circuit;
5, At design time,Power supply to this product should use analogLDO,Avoid using switching power supplies,Such asDC\DCConverter,The device may increase noise,Affect image quality;
6,FPCIf there is a bend during installation, ensure that it is not less thanR0.5Corner transition to ensureFPCperformance.
The lens renderings of different angles are as follows:
Reminder: apply toAndroidAndroid,LinuxSystem equipment(Computer, tablet, set-top box)Please confirm whether your device supports Microsoft standardsUVCUniversal drive agreement? not supportUVCThe equipment of the agreement cannot be used. Whether to support the standardUVCprotocol? Please ask your equipment manufacturer.
Salesman:Miss Cheng 13537758528
The company supports development and customizationCMOSCamera module, the existing module can be customized camera size, each camera can be equipped with a different angle lens(Except autofocus), If you have special requirements before buying, you can contact the seller to explain the purpose first, and we will try our best to match the lens suitable for your use.
Welcome customers to the factory to negotiate.
Factory address:West of Caowei First Industrial Zone, Xixiang Street, Baoan District, Shenzhen7floorGolden Qianxiang Technology Co., Ltd.
Nearby transportation:
1. Subway“Luobao Line”of“Hoorui Station”AExit straight300Meter
2. Bus stop name“Airport logistics”, The factory is behind the bus stop sign50Meter
3. Please navigate while driving“Caowei Park”, The factory is next to the park
Read before buying:
Borrow samples:In order to facilitate the testing needs of our customers, our camera module can provide sample testing, but it also needs to be shipped under Taobao. The round-trip cost of the test sample is paid by the buyer, and the sample can be provided free of charge10Test time in days. Note: When testing, take care of the samples, do not damage the samples, and ensure that the samples do not affect the secondary seller''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''s acceptance of returns.
Delivery time:The photos taken on the same day are usually sent out the next day, and we will try our best to arrange production samples. Under special circumstances, the seller will contact the buyer again. Bulk orders are subject to the negotiation time.
invoice:Customers who need to open ordinary invoices need to charge extra5%Tax point. For bulk orders, our company can also issue value-added tax invoices, plus additional charges12%Tax point. Generally, the goods will be sent first and the invoice will be sent later.